Brand

Rating

Price

Special Offers

Type

Size

Finish

Pack Quantity

Nailer & Brad Nails - Free UK Delivery Over £25 - Buy Online | Zoro

BT13 Series 18 gauge brown brad nails for use with the Bostitch brad nailer.  Finish nails (brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments.  28° Collation Angle  Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx. 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out.  (Remember only tools fitted with sequential trip should be used when working up a ladder).  Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them.  Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater.  Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.  Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

These 23 gauge mini pins are headless fine wire pins that are indispensible for fine molding and trim work. As the pins are completely headless , the wood closes over them after driving eliminating the need for time consuming fillingThey are also excellent for temporary tacking whilst glue dries, as they can be removed with little damage to the work.For use with the Bostitch headless pinner.

BT Series galvanised 18 gauge brad fasteners for use with the Bostitch Finish Bradders. Joined with an adhesive coating that holds the brads together.  Finish nails (brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries.

Bostitch FAC Series Flat Angle Coil Pattern Ring Coil Nails are designed for high volume operation. The coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them used in the pallet and crate, fencing, garden furniture and the construction industries.  To Suit:  N71C-1-E, N75C-2-E, N80CB-1ML, N89C-1P-E, N89C-2K-E  All Coil Nails are Round Head nails.  Typically:  Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails.  Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails.  Roofing nail coils contain 120 nails, due to the extra large diameter of the head.  15° Collation Angle  Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.  Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.

Finish nails and brads have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank, ensuring that their holding power is enhanced. Applications include partition walls, shop and bar fitting, light framing and timber construction and most second fit applications.  For use with N62FN-1, N62FNB-E & N62FNK-2 models.  Note: This nail will also fit the N60FN and the N59FNK models.  Applications - Partition walls, shop and bar fitting, light framing and timber construction and most second fit applications.  25° collation angle

Finish Nails have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank. This ensures that their holding power is enhanced, but of course the pull through force is lower than for nails with larger, Round or Clipped Heads. Primarily used for finish and trim work in the construction and joinery industries.

High carbon Zinc Dichromate HCFN finish nail 15 gauge. For use with Bostitch concrete block nailer.

Flooring L Cleats for use with the Bostitch flooring nailer.  L Cleat Finish: Galvanised

Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries.  All Coil Nails are Round Head nails.  Typically:  Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails.  Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails.  Roofing nail coils contain 120 nails, due to the extra large diameter of the head.  15° Collation angle  Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail.  Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish.  Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.  For use with:  N57C-1CE heavy-duty Coil Nailer  N58C-1-E Coil Nailer  N58C-1-E Coil Nailer  N66C-2-E Coil Nailer

Nailer & Brad Nails

BT13 Series 18 gauge brown brad nails for use with the Bostitch brad nailer. Finish nails (brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries. Length 32mm. Colour Brown. Pack Clam pack of 1000.

BT1332-32 1M Brown Brad Nails 32mm (Pack 1000) BOSBT1332B1M

Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28 Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx. 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. Gauge/Diameter (mm) 3.1 Length 90 28 Collation Angle SKU S31090 Profile PLAIN Finish BRIGHT Description STICK NAIL 3.10-90 PLAIN 2M Qty per box 2000 Will also fit the N80SB, FW28WW-E, N100S

28 Bright Smooth Shank Stick Nails 3.1 x 90mm (Pack 2000) BOSS31090

These 23 gauge mini pins are headless fine wire pins that are indispensible for fine molding and trim work. As the pins are completely headless , the wood closes over them after driving eliminating the need for time consuming filling They are also excellent for temporary tacking whilst glue dries, as they can be removed with little damage to the work. For use with the Bostitch headless pinner. Length 30mm SKU 106300SE Finish STANOX (Copperwash) Description Mini Pin 30mm Stanox Qty per box 10000 Suits TU216-2330 Tacker

Stanox Mini Pins 1063000 30mm (Pack 10,000) BOS1063000

BT Series galvanised 18 gauge brad fasteners for use with the Bostitch Finish Bradders. Joined with an adhesive coating that holds the brads together. Finish nails (brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries. Gauge/Diameter (mm) 18 GA Length 50 SKU BT1350GA Finish GALV Description MINIBRADS 50 GALVA 5M Qty per box 5000

BT13-50-Galvanised Brad Nails 50mm (Pack 5000) BOSBT1350GA5

Bostitch FAC Series Flat Angle Coil Pattern Ring Coil Nails are designed for high volume operation. The coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them used in the pallet and crate, fencing, garden furniture and the construction industries. To Suit N71C-1-E, N75C-2-E, N80CB-1ML, N89C-1P-E, N89C-2K-E All Coil Nails are Round Head nails. Typically Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15 Collation Angle Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. Finish Galvanised. Size 2.8 x 65mm. Box quantity 7,500.

Galvanised Ring Shank Coil Nails 2.8 x 65mm (Pack 7500) BOSF280R65GQ

Finish nails and brads have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank, ensuring that their holding power is enhanced. Applications include partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. For use with N62FN-1, N62FNB-E & N62FNK-2 models. Note This nail will also fit the N60FN and the N59FNK models. Applications - Partition walls, shop and bar fitting, light framing and timber construction and most second fit applications. 25 collation angle Type - 15 gauge angled finish nail. Finish - Galvanised. Length - 44mm. QTY - Box 3655.

15 Gauge Angled Galvanised Finish Nails 44mm (Pack 3655) BOSFN1528

Finish Nails have heads that are rectangular. They are the same width as the shank, but the breadth of them is greater than the shank. This ensures that their holding power is enhanced, but of course the pull through force is lower than for nails with larger, Round or Clipped Heads. Primarily used for finish and trim work in the construction and joinery industries. A Bulk Pack of 2,500 44 mm 16 Gauge Straight Finish Nails for use with Stanley Bostitch Finish Nailers. Length 44 mm. Pack Box of 2500.

SB16-1.75 Straight Finish Nail 44mm Galvanised (Pack 2500) BOSSB16175BK

The Bostitch 21684B-E wide crown stapler is a professional grade headless pinner with a small compact design for better access to the workspace, variable power control and a secondary safety trigger. Suitable for furniture manufacture, ideal for moulding and trim work. Weight 0.83 kg Dimensions Length 221 mm & times Width 150 mm & times Height 40 mm Staple Length 4 mm (min) - 16 mm (max) Diameter 0.5 mm (min) - 1 mm (max) Magazine Capacity 125 (max) Operating Pressure PSI 80 - 120 BAR 4.9 - 8.4 Air Consumption Ltr.per shot @ 5.6 bar 0.17 Noise LPA 1sd 64.4 LWA 1sd 74.0 LPA 1s, 1m 61.0 Vibration m/s2

21684B-E Pneumatic Wide Crown Stapler 84 Series BOS21684BE

High carbon Zinc Dichromate HCFN finish nail 15 gauge. For use with Bostitch concrete block nailer. 50mm Gauge/Diameter (mm) 15 Ga Box 1500 High Carbon Zinc Dichromate Suits SB-HC50FN

HCFN-50 15 Gauge Hardened Nails 50mm (Pack 1500) BOSHCFN50

BT Series galvanised 18 gauge brad fasteners for use with the Bostitch Finish Bradders. Joined with an adhesive coating that holds the brads together. Finish nails (brads) are normally of a rectangular cross section instead of being round. Their diameters are less than the coil and stick nails, and are primarily used for finish and trim work in the construction and joinery industries. Gauge/Diameter (mm) 18 GA Length 45 SKU BT1345GA Finish GALV Description MINIBRADS 45-GALVA 5M Qty per box 5000

BT13-45-Galvanised Brad Nails 45mm (Pack 5000) BOSBT1345GA5

Flooring L Cleats for use with the Bostitch flooring nailer. L Cleat Finish Galvanised L Cleat Length 50mm Qty. Box 1000

FLN-200 Flooring Cleat Nails 50mm (Pack 1000) BOSFLN200

Designed for high volume operation, coils contain large quantities of nails meaning that reloading down time can be kept to a minimum. You will find them in the pallet and crate, fencing, garden furniture and the construction industries. All Coil Nails are Round Head nails. Typically Coils of nails with diameters from 2.0 mm to 2.2 mm contain 350 nails. Coils of nails with diameters from 2.5 mm to 3.1 mm. Contain 225 nails. Roofing nail coils contain 120 nails, due to the extra large diameter of the head. 15 Collation angle Ring shank nails have a series of rings punched into the surface of the shank. A difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising, or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails. For use with N57C-1CE heavy-duty Coil Nailer N58C-1-E Coil Nailer N58C-1-E Coil Nailer N66C-2-E Coil Nailer Finish Galvanised. Size 2.3 x 50mm. Boz quantity 13,200.

Galvanised Ring Shank Coil Nails 2.3 x 50mm (Pack 13,200) BOSN230R50GQ

Galvanised ring nail anchor stick for use with N88RH-2MCN-E only when MCN is fitted. Galvanised to 15 microns. Ring shank with conical head which centres the nail in the pre-drilled hole. Gauge/Diameter (mm) 4 Length 38 21 Collation Angle Profile RING Finish G8 Description ANCHOR STICK 4 .00-38 RING GAL 2M Qty per box 2000 Fits F21PL-E For use with N88RH-2MCN-E only when MCN is fitted Note MCN nails are only for use with MCN Tip.

Browse our original Bostitch products in Nailer & Brad Nails

We suggest upgrading to Chrome