Brand

Rating

Price

Special Offers

Type

T-Slot Size

Standards Met

Maximum Spindle Speed

Minimum Spindle Speed

Minimum Spindle to Table

Overall Height

Overall Length

Overall Width

Number of T-Slots

Milling Machines - Free UK Delivery Over £25 - Buy Online | Zoro

SLAC-WH1 is one of the first vice stop manufactured by a machinist with the CNC machinist in mind. Its low-profile design can stay completely below the top surface of the vice to enable it to not interfere with cutting tool paths. Whether you are making 1 part or 1000 parts, the SLAC-WH1 stop will not move once you lock it down by the grub screws located on the sides. It is an ideal datum point to locate parts. 

The stop has two adjustable non-marking flat point grub screws for moving the position in X axis and can easily be removed once the workpiece is clamped, this allows the component to be machined all the way round.

You can also use SLAC-WH1 on the opposite side of the vice, so a duel set up is made available on the same vice, reducing set up and loading time by at least 60 percent. 

Simply bolt SLAC-WH1 to the side of the vice, set the location where you would like the stop rod position to be. Suitable for all vices whether it is 4”, 5” or a 6” vice.

SLAC-WH1 is designed and manufactured in the UK. The body is made from aerospace grade aluminium and stop rod from hardened stainless steel.

Technical Details:

• Manufactured in the UK
• Comes in Red for enhanced visibility or clear.
• SLAC-WH1 fits all vices with a tapped hole on each side of the vice
• Reduce your set up times by up to 60% compared to other workstops.
• Kit comes with SLAC workholding lever arm, hardened stop rod, side bolt, two washers and two non marking grub screws.

Instructions:

1. Determine the location of where SLAC-WH1 would be positioned so that body and stop rod do not interfere with tool paths, ensure material stops at position, once determined, tighten with the supplied bolt into the vice.

2. Position stop pin to desired X Axis and tighten grub screws.

Powerful brushless drive with particularly smooth running, as well as high performance with approximately constant torque over the entire speed range. Best power transmission through aluminium pulleys in combination with toothed gates quality wedge belt. High smoothness thanks to ground multi-tooth handle. Concentricity guaranteed to be less than 0.015mm measured in the drill. Separate emergency stop switch. Digital speed display integrated in the housing. High quality Optimum quick release drill chuck as standard. Large sized height adjustable protective screen with safety switch for maximum protection of the user. Drilling depth stop. V-belt cover with safety switch. V-belt clamping device. Right/Left run.  Machine light in the drill head integrated. Precisely worked, stable drilling table with 2 diagonally running T-slots 360 rotatable and circumferential cooling water channel. Thick walled casting column. Massive base plate.

A must for model makers. Bench mounted, this Milling/Drilling machine has a spindle rotation of of up to 45°, making it a very capable tool. An assortment of useful accessories are available. This versatile tool has been manufactured to meet European Machinery Directive 98/37/EC and is both CE and RoHS compliant. 

Specifications:
Swing over bed: 180mm.
Drilling capacity: 13mm.
End milling capacity: 16mm.
Face milling capacity: 30mm.
Headstock travel (Z): 180mm.
Cross axis: 100mm.
Longitudinal axis: 220mm.
Spindle rotary angle: +/-45°.
Output power: 350W.
Spindle speed: Low range 0-1100rpm +/-10%. High range: 0-2500rpm +/-10%.
Spindle taper: MT3 or R8.
T-slot: 12mm.
Net/gross weight: 50/68kg.
Packing size: 540 x 500 x 760mm.

FOR DIY USE
Not warranted for industrial use.

Mini Milling/Drilling Machine

316-12FM650-12000L Milling Head Grade 1730 316

Bench mounting mini milling/drilling machine which will handle most materials. Incorporates a working table with T slots to enable clamping or workpieces and metric graduated compound scales. Column tilts from 0-45� from vertical. No-volt switch to prevent accidental switch on and approved three pin cable and approved plug. Carton packed.|Drilling capacity13mmFace milling capacity30mmEnd milling capacity16mmHeadstock travel180mmCross axis100mmLongitudinal axis220mmSpindle tilt axis �0-45 �Spindle taperMT3Low spindle speed 100-1100r/minHigh spindle speed100-2500r/minT-slot12mmThroat depth170mmTable size390 x 92mmWeight60kg|No-volt switch

500W Milling Machine - 34023-DP

Bench mounting mini drilling/milling machine with the flexibility to handle most materials. Features include a 350W motor, variable speed drive, working table with T-slots to enable clamping of workpieces and Metric graduated compound scales. The machine also incorporates a tilting column which allows drilling/milling of workpiece at ±45° from vertical. Supplied with 13mm chuck accessory kit for adjusting and setting. An optional stand is available, order Model No. SM3002ST.

Mini Drilling & Milling Machine

Versatile Machine for drilling - milling & boring operations. Heavy duty & sturdy machine made with a generous size meehanite casting. Rated for continuous use & long life expectancy. Made to accurate engineering tolerances by highly skilled engineers during manufacture. 3 HP Motor allows larger cuts to be taken during production runs. R8 spindle allows a large selection of standard tooling to be used. Automatic stop to up/down feed at the end of the preset travel. Angular positioning to left/right through worm & gear for ease. Reversible switch allows the spindle to run clockwise & anti-clockwise. Centralised one shot lubrication ensures lubrication to all parts that are otherwise inaccessible. DRO allows you to work in either imperial or metric calibrations. Hardened slide ways give the machine a much longer production life. Quill feed at 3 rates of Feed give you the option to select the correct feed to quill to suit your individual production requirements. Servo type variable & rapid feeds are available for both longitudinal & cross feeds. Electrically Interlocked spindle guard conforms to the latest CE regulations & health & safety standards. 3 Axis DRO.

ETM-3VS Turret Mill - 1-199-300

Heavy, sturdy & solid columns made of premium cast material with ground and shaven dovetail guide for excellent stability and precision. Clockwise/Anti-clockwise rotation. Excellent concentricity thanks to tapered roller bearings, better than 0.015mm measured in the spindle sleeve. Gear head pivots through 60°. Manual fine feed. Drilling depth stop. Thread tapping mode. Two-stage industrial quality electric motor.

MH35V Tilting Head Drill-mill

Counterweight facilitates Z axis adjustment. Variable speed control. Easy tool change with quick clamping system. Wide guide rails on Z axis. Groove prepared for easy retroactive mounting of magnetic strips. Inverter motor. Feed spindles can be adjustable spindle nuts. All guides are ground and finish shaved (oil pockets for lubrication). Precision workmanship. Particularly smooth action. Angular ball bearings on the axes. Head pivots through ± 45°. Right-hand/left-hand rotation. Height-adjustable protective screen with microswitch. Sturdy dovetail guide, precision ground and shaved with adjustable wedge rails. Easily readable speed display with milling head.

MH25V Vario Drill-mill

SLAC-WH1 is one of the first vice stop manufactured by a machinist with the CNC machinist in mind. Its low-profile design can stay completely below the top surface of the vice to enable it to not interfere with cutting tool paths. Whether you are making 1 part or 1000 parts, the SLAC-WH1 stop will not move once you lock it down by the grub screws located on the sides. It is an ideal datum point to locate parts. 

The stop has two adjustable non-marking flat point grub screws for moving the position in X axis and can easily be removed once the workpiece is clamped, this allows the component to be machined all the way round.

You can also use SLAC-WH1 on the opposite side of the vice, so a duel set up is made available on the same vice, reducing set up and loading time by at least 60 percent. 

Simply bolt SLAC-WH1 to the side of the vice, set the location where you would like the stop rod position to be. Suitable for all vices whether it is 4”, 5” or a 6” vice.

SLAC-WH1 is designed and manufactured in the UK. The body is made from aerospace grade aluminium and stop rod from hardened stainless steel.

Technical Details:

• Manufactured in the UK
• Comes in Red for enhanced visibility or clear.
• SLAC-WH1 fits all vices with a tapped hole on each side of the vice
• Reduce your set up times by up to 60% compared to other workstops.
• Kit comes with SLAC workholding lever arm, hardened stop rod, side bolt, two washers and two non marking grub screws.

Instructions:

1. Determine the location of where SLAC-WH1 would be positioned so that body and stop rod do not interfere with tool paths, ensure material stops at position, once determined, tighten with the supplied bolt into the vice.

2. Position stop pin to desired X Axis and tighten grub screws.

End Stop for Milling Machine Vices Clear

HURON type milling head, 360° tiltableCoolant system + LED light as standard3-axis viewer, integrated in the control panel, rotatable to R and LAutomatic feeds on X, Y and Z axes + rapid feeds.Drilling Ø 40 Cast iron and Ø 32 Steel400V / 3KwTable 1370 x 300mm

JM125-DRO Vertical Mill

ETM-2VS R8 Variable Speed 1-199-200
3 AXIS DRO - Power feed to three axis. Versatile machine for drilling - milling and boring operations. Heavy-duty and sturdy machine is made of meehanite casting of generous proportion. Rigid machine is rated for continuous use and will give you longer life expectancy. Accurate engineering tolerances have been met by highly skilled engineers during manufacture. 3hp motor allows you to take large cuts during your production runs. R8 spindle allows you to use a large selection of standard tooling. Automatic stop is to up/down feed at the end of the pre-set travel. Angular positioning to left/right through worm and gear for ease. Reversible switch allows you to run spindle clock and counter clockwise. Centralised one shot lubrication ensures lubrication to all parts otherwise inaccessible. Metric dials with DRO allow you to work in either inch or metric calibrations. Hardened slide ways gives the machine much longer production life. Quill feed at three rates of feed give you the option to select the correct feed to quill to suit your individual production requirements. Servo type variable longitudinal cross and vertical feed and rapid. Electrically interlocked spindle guard conforms to the latest CE regulations and Health and Safety Standards.
Standard accessories:
Power feed to quill - three rates. Servo type longitudinal, cross and vertical feed and rapid. One shot lubrication. Coolant system. Electrically interlocked spindle guard. 
Low volt machine light.

Specifications:
Table size: 228 x 1245mm.
Table travel (long): 838mm.
Saddle travel (cross): 300mm.
Knee travel (vertical): 400mm.
Quill travel: 127mm.
Ram travel: 315mm.
Spindle motor: 2.2kW (3hp).
Spindle taper: R8.
Quill power feed: 0.04, 0.08, 0.15mm/rev.
Spindle speeds: 70 - 4200 variable speed.
Overall length: 1700mm.
Overall width: 1600mm.
Overall height: 2130mm.
Spindle to table: min. 0mm, max. 415mm.
Spindle to column: min. 170mm, max. 485mm.

ETM-2VS Vari Turret Milling Machine

AJT-200
Turret Milling Machine with fully universal turret head
On swivel turret ram, one shot lubrication, Variable speed head. These machines are ergonomically designed, combining the latest design techniques with the highest standard of quality engineering, reliability in service, accuracy and rigidity of machine. Includes infinitely variable speeds enabling the operator to machine wider variety of more sophisticated materials.

Main Features:.
Chrome dovetail slideways
Servo power feed to x-axis.
One shot lubrication.
Spindle guard.
Swarf tray.
Coolant system.
Toolbox and manual.
3hp main motor.
CE mark.
Standard equipment
Electronically controlled Servo Drive to the table to provide
Longitudinal feed and rapid traverse
Halogen worklight
Chrome slides
Hand scraped table top
Coolant Pump and fittings
Safety Guard
One Shot Lubrication
Toolkit


Working Surface:1,270 x 230mm.
Tee - Slots, Number & Size:  3 x 16mm.
Tee - Slot Centres: 63mm.
Long Travel: 880mm Manual / 760mm Feed.
Cross Travel: 320mm Manual / 305mm Feed (opt).
Vertical Travel:  400mm.
Distance Spindle Nose to Table:  57 - 463mm.	

Distance Spindle Centre to Column:  213 - 533mm.
Overarm Travel:  320mm.	
Spindle Quill Feeds: 0.04 / 0.08 / 0.15mm/rev. 
Spindle Quill Travel:127mm.
Spindle Taper: R8. 
Spindle Speed Range: 50 - 3,750 Variable. 
Motor Power: 3 Hp (2.2 kW). 
Swivel Angle left to right:  +/- 90 ˚ .
Swivel Angle front to back: +/- 45 ˚ .
Ram Swivel: 360 ˚ .
Machine Dimensions (LxWxH): 1,450 x 1,400  x 2,100mm.
Weight: 1,150 Kg.

AJT200 Industrial Universal R8 V/Speed Turret Mill

DH28FS Upright Drill 3PH

Turret Mill - TM600

Turret Mill - AJT200

CNC Mini Mill - AJPR220

OPTImill MB 4P Drilling-milling Machine (3 Phase 400v)
Universal drilling and milling machines with digital position indicator DRO 5, powerfeed, and cast iron machine base

Find Milling Machines Products

We suggest upgrading to Chrome